15094-4
PREFABRICATED PIPE HANGERS, SUPPORTS AND BRACING
sheet and galvanized protection shield; isolators similar to Eleen, Figure No. 228; or
PVC-coated hangers and supports. All stainless steel piping shall be isolated from
all ferrous materials, including galvanized steel, by use of neoprene sheet material
and protection shields, similar to above methods.
15094-3
PREFABRICATED PIPE HANGERS, SUPPORTS AND BRACING
15094-2
PREFABRICATED PIPE HANGERS, SUPPORTS AND BRACING
shown on the Contract Drawings are specified elsewhere and not required as part of
this Specification.
Pipes supports shall be classified as one of the following:
1. Type 1 — Supported from an overhead structural member using overhead
hangers, guides, clevises, rollers, clamps or other means as specified herein.
2. Type 2 - Supported from a structural member below the pipe using guides,
rollers, clamps, saddles or other means as specified herein.
15094-1
SECTION 15094
PREFABRICATED PIPE HANGERS, SUPPORTS AND BRACING
PART 1 - GENERAL
1.1
1.2
1.3
1.4
DESCRIPTION
A.
3, Con
a.
b.
Cc.
d.
B. Rubber Li
15092-2
PIPE SLEEVES & SEALS
PART 1 - GENERAL
1.1 DESCRIPTION
15092-1
SECTION 15092
PIPE SLEEVES & SEALS
A. Work Included: Furnish and install wall sleeves and seals of the type(s) and sizes(s)
and in the location(s) shown on the Drawings and specified herein.
B. Related Work Specified Elsewhere:
1. Firestopping is specified in Section 07270.
2 Sealants are specified in Section 07900.
3. | Plumbing - General is specified in Section 15400.
4. HVAC - General is specified in Section 15600.
12 QUALITY ASSURANCE
15063-2
COPPER PIPE & FITTINGS
(INTERIOR APPLICATIONS)
f. Form continuous solder beads around the entire circumferences of the
joints.
Bending Pipe:
1. Bend pipe by the method and to the radius to comply with the manufacturer's
recommendation.
2. Bends shall be free of any cracks or buckles.
Support: Support all pipes in accordance with the "Pipe Hangers & Supports"
Section in this Division.
15063-1
SECTION 15063
COPPER PIPE & FITTINGS
(INTERIOR APPLICATIONS)
PART 1 - GENERAL
1.1 DESCRIPTION
A. Work Included: Furnish and install copper pipe and fittings of the type(s) and
size(s) and in the location(s) shown on the Drawings and as specified herein.
B. Related Work Specified Elsewhere:
1. Pipe & Pipe Fittings - General is specified in this Division.
1.2 QUALITY ASSURANCE
A. Pipe: Seamless copper water tube, ASTM B88 (pressure) and ASTM B-306
atmospheric.
PART 2 - PRODUCTS
mo
15061-2
STEEL PIPE & FITTINGS
4. Make up joints with an approved pipe joint compound or tape applied to the
male threads only.
5. When connecting pipes to recessed drainage fittings, seat them against the
shoulder of the fittings.
6. | When required to back off joints, entirely disjoint, wipe the threads of both the
pipe and fittings clean, apply new joint compound, and reassemble the
connection.
Welded Connections:
1. All welding shall conform to ANSI B31.1.
PART 1 - GENERAL
1.1 DESCRIPTION
15061-1
SECTION 15061
STEEL PIPE & FITTINGS
A. Work Included: Furnish and install steel pipe and fittings of the type(s) and size(s)
and in the location(s) shown on the Drawings and as specified herein.
B. Related Work Specified Elsewhere (When Applicable): "Pipe and Pipe Fittings -
General" is specified in this Division.
PART 2 - PRODUCTS
2.1 MATERIALS
