Gamehme;
PART 5 - INSTALLATION (Continued)
ADA Rolled - This is the type of edge to meet the requirements of ASTM 1951, Specifications
for Determination of Accessibility of Surface Systems Under and Around Playground Equipment.
The rolled edge will require additional materials in order to provide adequate ADA Wheelchair
access. The total linear feet of the pad will need to be provided if the whole site is to be ADA
compliant.
PART 5 - INSTALLATION:
Weather Conditions. - Because the polyurethane agents are moisture or heat sensitive, the
nighttime temperatures must be above 40 degrees with daytime temperatures around 50
degrees. These temperatures must be consistent for several days before and after the poured
rubber installation period. Complying with these weather conditions will prevent poured rubber
from freezing which prevents proper curing.
Gamelhme;
PART 3 -SUB-BASE TYPES & DETAILS (Continued)
Stone Graduation U.S. Sieve Percent Passing
1" 100
3/4" 90 - 100
No. 4 35 - 60
No. 30 10- 30
No. 200 2-9
ie |
PART 2 - MATERIAL DATA (Continued)
Colors - The color of GT Impax recycled poured rubber surfacing will be indicated on plans.
Owner or owner's representative will be responsible for selecting standard blends. Selection of
either standard color blends or custom color blends must be made at time quotation is being
requested. EPDM/TPV colors are available in 100% black and a variety of colors. Ask your
GameTime representative for available color combinations.
PSI and minimum % elongation @ break of 140%.
IPEMA Certification: Manufacturer must provide proof of certification. “In the interest of
public playground safety, IPEMA provides an independent laboratory which validates a
manufacturer's certification of conformance to ASTM F1292-04. A list of current validated
products, their thickness and critical heights may be viewed at www.ipema.org.”
Submittal Details:
Poured in Place
Product Specification
PART 1 - GENERAL
Work Details:
This work includes furnishing and installing GT Impax recycled poured rubber surfacing.
A. Remove adhesive spills from playground safety surfacing tiles in accordance with
manufacturer's instructions.
B. Clean tiles in accordance with manufacturer's instructions.
3.6 PROTECTION
A. Protect playground safety surfacing tiles from foot traffic for a minimum of 12 hours
after installation.
B. Protect completed tiles from damage during construction.
c MEASUREMENT AND PAYMENT
5 Scarify existing asphalt in accordance with manufacturer's instructions.
6. Variations in Elevation: Repair variations in elevation of completed subsurface greater
than_plus or minus 1/4 inch over 10 feet in any direction.
B. Ramps:
i
Z.
3.
Prefabricated Ramps: “SofRAMP Jr.”.
Prefabricated ADA-Compliant Ramps: “SofRAMP ADA”.
Material: Same as playground safety surfacing tiles.
CG. Adhesive: Furnished by manufacturer.
PART 3 EXECUTION
3.1 EXAMINATION
A. Examine areas to receive playground safety surfacing tiles. Notify Architect if areas are
not acceptable. Do not begin installation until unacceptable conditions have been
corrected.
3.2 PREPARATION
1) Percent Color: [25 percent color, 75 percent black] [50 percent color,
50 percent black] [75 percent color, 25 percent black] [90 percent
color, 10 percent black].
: Test Results:
i, Impact Attenuation, ASTM F 1292:
a. q-max Score: Less than 125.
b. Head Injury Criteria (HIC) Score: Less than 700.
2; Freeze Thaw, ASTM C 67: No deterioration.
5. Rubber Deterioration/Air Oven, ASTM D573: No deterioration.
4. Slip Resistance:
a. ASTM E 303:
4d Dry: 51 minimum.
2) Wet: 44 minimum.
b. ASTM D 2047:
