Finance Committee

PART 1 - GENERAL

1.1 DESCRIPTION

15092-1

SECTION 15092

PIPE SLEEVES & SEALS

A. Work Included: Furnish and install wall sleeves and seals of the type(s) and sizes(s)
and in the location(s) shown on the Drawings and specified herein.
B. Related Work Specified Elsewhere:
1. Firestopping is specified in Section 07270.
2 Sealants are specified in Section 07900.
3. | Plumbing - General is specified in Section 15400.
4. HVAC - General is specified in Section 15600.

12 QUALITY ASSURANCE

15063-2
COPPER PIPE & FITTINGS
(INTERIOR APPLICATIONS)

f. Form continuous solder beads around the entire circumferences of the

joints.
Bending Pipe:
1. Bend pipe by the method and to the radius to comply with the manufacturer's
recommendation.

2. Bends shall be free of any cracks or buckles.

Support: Support all pipes in accordance with the "Pipe Hangers & Supports"
Section in this Division.

15063-1

SECTION 15063

COPPER PIPE & FITTINGS
(INTERIOR APPLICATIONS)

PART 1 - GENERAL

1.1 DESCRIPTION
A. Work Included: Furnish and install copper pipe and fittings of the type(s) and
size(s) and in the location(s) shown on the Drawings and as specified herein.
B. Related Work Specified Elsewhere:
1. Pipe & Pipe Fittings - General is specified in this Division.

1.2 QUALITY ASSURANCE
A. Pipe: Seamless copper water tube, ASTM B88 (pressure) and ASTM B-306
atmospheric.

PART 2 - PRODUCTS

mo

15061-2
STEEL PIPE & FITTINGS

4. Make up joints with an approved pipe joint compound or tape applied to the
male threads only.

5. When connecting pipes to recessed drainage fittings, seat them against the
shoulder of the fittings.

6. | When required to back off joints, entirely disjoint, wipe the threads of both the
pipe and fittings clean, apply new joint compound, and reassemble the
connection.

Welded Connections:

1. All welding shall conform to ANSI B31.1.

PART 1 - GENERAL

1.1 DESCRIPTION

15061-1

SECTION 15061

STEEL PIPE & FITTINGS

A. Work Included: Furnish and install steel pipe and fittings of the type(s) and size(s)
and in the location(s) shown on the Drawings and as specified herein.

B. Related Work Specified Elsewhere (When Applicable): "Pipe and Pipe Fittings -
General" is specified in this Division.

PART 2 - PRODUCTS

2.1 MATERIALS

15051-2
POLYVINYL CHLORIDE (PVC) DRAINAGE PIPE

15051-1

SECTION 15051

POLYVINYL CHLORIDE (PVC) DRAINAGE PIPE

PART 1 - GENERAL

1.1 DESCRIPTION
A. Work Included: Furnish and install PVC drainage pipe and fittings of the type (s)
and size (s) and in the location (s) shown on the Drawings and as specified herein.
B. Related Work Specified Elsewhere: "Pipe & Pipe Fittings - General" is specified in
this Division.

12 QUALITY ASSURANCE
A. Standards:

1. Pipe and fittings (interior) shall conform to ASTM D-2665S.

3.

4.

15050-3
PIPE & PIPE FITTINGS — GENERAL

O

mimo

15050-2
PIPE & PIPE FITTINGS — GENERAL

Store materials on the project site in enclosures or under protective coverings in
accordance with manufacturer's recommendations and as required by the Engineer.
Assure that materials are kept clean and dry.

Do not store materials directly on the ground.

Follow manufacturer's specific instructions, recommendations and requirements.

PART 2 - PRODUCTS

2.1 MATERIALS

A.

Materials are specified in the following Sections in this Division.

15050-1

SECTION 15050

PIPE & PIPE FITTINGS — GENERAL

PART 1 - GENERAL

1.1

1.2

1.3

1.4

1.5

DESCRIPTION

A. Work Included: Furnish, install, support, and test pipe and pipe fittings of the type(s)
and size(s) and in the location(s) shown on the Drawings and as specified herein.

B. Related Work Specified Elsewhere (When Applicable):
1. Valves, gates, pipe hangers, pipe supports, pipe and equipment insulation,

heating, and plumbing are specified in the appropriate Sections in Division 15.