Agenda

STATE OF NEW HAMPSHIRE
Depariment of Adminisirative Services
Division of Procurement and Support Services
Bureau of purchase and Property
Concord, New Hampshire 03301
DATE: October 26, 2018

NOTICE OF CONTRACT
CONTRACT: AMMUNITION - Speer & Federal
CONTRACT NO.: 8002360
NIGP CODE: 680-0400
CONTRACTOR: EAGLE POINT GUN CONTRACTOR# 166490
1707 THIRD STREET
THOROFARE NJ 08086

CONTACT PERSON: THOMAS J. MORRIS Iil

TELEPHONE. NO.: 856-848-6945
FACSIMILE. NO.: 856-384-2938

NASHUA POLICE
Date: 14 February 2018

DEPARTMENT

Intradepartmental Communication

To: Dan Kooken, Purchasing Manager
From: Karen A. Smith, Business Manager

Subject: Nashua Police Department ammunition and supplies

The below request is to purchase arnmmunition. The State of NH contract #8002360 awarded to Eagle
Point Gun/TJ Morris & Son is effective through Ocicber 31, 2020.

THE CITY OF NASHUA “The Cate City’

Financial Services

Purchasing Department

February 28, 2019
Memo #19-120

TO: MAYOR DONCHESS
FINANCE COMMITTEE

SUBJECT: PURCHASE OF NPD AMMUNITION (VALUE: $77,924)
DEPARTMENT: 150 POLICE; FUND: AMMUNITION AND SUPPLIES ACCOUNT

Please see attached communications from Karen A. Smith, Business Manager dated February 14, 2019
for the information related to this purchase.

7:00 pm

FINANCE COMMITTEE

MARCH 6, 2019
Aldermanic Chamber

ROLL CALL

PUBLIC COMMENT

COMMUNICATIONS

From:
Re:

From:

Re:

From:
Re:

From:

Re:

From:
Re:

From:
Re:

From:

Re:

From:
Re:

Dan Kooken, Purchasing Manager
Purchase of NPD Ammunition (Value: $77,924); Department: 150 Police; Fund: Ammunition and
Supplies Account

3.3

All instrumentation shall be installed in accordance with the manufacturers’
installation requirements.

Flush chips and other debris from piping before installing flow meter.

Install flow meters to allow minimum 5 pipe diameters in straight pipe
upstream and 2 pipe diameters downstream from any valves or fittings. Verify
that this requirement has been met prior to installation of the flow meter.

2.7. SIGNAL WIRING

A. Wiring from the control panel to sensors at the Sump Riser Building shall be
single- or multi-pair, #20 AWG stranded copper wire, twisted, 100 percent
aluminum foil individually shielded pairs, with outer jacket. Acceptable
Manufacturer: Belden No. 8761 (1-pair), No. 9402 (2-pair), No. 9874 (6-pair).

2.6

B. Install aneroid bellows assembly for atmospheric pressure reference in the
junction box on the leachate sump side riser pipes, unless otherwise noted.
Use manufacturer-supplied vented cable full length to bellows.

C. Level transmitters shall be intrinsically safe. Circuit shall be rendered
intrinsically safe by Zener Barrier in the control panel.

D. Acceptable Manufacturer: WIKA Instrument Corporation IL-10 transducer
with Pressure Systems, Inc. Series 815 Aneroid Bellows.

E. Schedule:

Gauge shall be bottom outlet, flush mounted style, with %-inch NPT stainless
steel connection. Pressure range shall be 0 to 100 pounds per square inch

gauge (psig).

Provide each pressure gauge with a plug type, isolation valve as indicated on
the Drawings to allow removal of the gauge under operating pressure.

2.3. LEVELSWITCH AND HOLDER

A.

B.

H.

I.

The level switch shall be float type, with reed switch.

SECTION 16500

INSTRUMENTATION AND CONTROLS

PART 1 - GENERAL

1.1

1.2

1.3

SCOPE

A. Work under this Section includes all metering and control equipment to be
furnished as part of the control system, and all signal wiring.

3.4

3.5

3.6

3.7

OUTLET AND JUNCTION BOXES

A. Outlet and junction boxes shall be installed in a workmanlike manner, rigidly
supported and properly aligned. Do not rough-in boxes back-to-back.

MOUNTING HEIGHTS

A. Wiring devices and other equipment shall, unless noted otherwise, be mounted
with respect to the indicated surface as follows:

Receptacles: 4 feet - 0 inches above finish grade
Switches: 4 feet - 6 inches above finish grade
Control Panel: 6 feet - 6 inches to top above finish grade